How to Repair Bifold Door Top Roller Guide

If your bifold door is squeaking then it's likely that they need some attention. It is possible that you need to clean, lubricate or adjust them. The issue could be caused by loose bolts at the top pivot or by the top guide roller.

This kit contains all the hardware needed to restore your bi fold door repairs-fold closet door to its optimal performance.

Remove the Door

Installing an internal set of bifold doors may appear to be a complicated and complicated task however, it's actually straightforward for a DIYer with a little experience. The frame isn't the problem however, getting the doors to fold and close smoothly is. Bifold doors are a complex piece of machinery and, as such, they might need some tuning up to ensure that they function properly. It could be as simple as tightening up a screw, or as complex as removing and replacing the pivot pin or roller.

You can usually resolve these problems with a few simple adjustments, without having to remove the doors. It is possible that your bifold doors are sliding or scraping the floor, or bouncing off the track. It's easy to fix these problems. Just follow three simple steps and your bifold door will be back in line in the shortest amount of time.

The most common issue internal bifolding doors face is that they slide out of alignment. This can be caused by loose screws or holes in the anchor pins, or simply a misaligned door. Most of the time, this can be corrected with a few simple adjustments. However, if your door doesn't move at all, you may have to replace it.

You'll have to take off the door with a screwdriver, and possibly a pair pliers to loosen any pivot pins that are too tight. The screwdriver is used to release the locking levers on the bottom bracket for pivots. The pliers are used to take off the pin.

When the top roller is free and the top roller is loose, you should be able to lift the door and swivel it downwards and allow you to pull it off of its track and pivot brackets. This is typically quite easy however be careful not to let the door hit against the door frame. Then you can sand the edge of the door to smooth it. You can then paint or refinish the door if required.

Take off the Roller Guide

This spring-loaded roller guide mounts on the top of the bifold door to assist in smooth operation. It is designed to be used with Kenna frames and will fit doors that are 1 to 1-3/8 inches thick. It is made from nylon, steel and plastic components. It can be used to replace a damaged or worn-out guide.

Remove any screws holding the roller guide in place using the screwdriver. Use your hands to slowly pull it from the frame. It might require some effort to lift the door, so make sure you ask a friend to help you.

Once the old guide is removed, carefully cut the remaining finish on the foot of the new guide with a razor blade to separate it from the rod blank. This will make it easier to remove and ensure that there is no damage to the new guide foot. Be cautious while doing this as the foot is very sharp and could cut or nick your fingers.

You may have to use some force to remove the guide, but you must be careful not to break or chip the foot. After you've separated the guide from the rod blank, make sure to get rid of all the epoxy and threads remaining in the area the guide was attached. This will prevent future problems with the guide.

After you have removed the guide, you can test the new guide by placing it in its place and then applying a few turns of masking tape or a kind of guide tubing to hold it in its place. This will let you double verify the guide's spacing and alignment to ensure everything is set up properly. This step is crucial to avoid any future issues regardless of whether you use the CRB Spine Finder & Deflection System or eyeball it.

If the guide is placed correctly and functioning according to its intended function then the final step is to put the door back in its place. Be aware that any screws or pins that you loosened or removed must be replaced and tightened appropriately after you've finished.

Remove the Bottom Pivot

Bifold doors make a gorgeous addition to any home but sometimes they need a little adjustment or tweaking to stay in good shape. While some of the simpler issues can be resolved by keeping the doors in place, other issues will require removal. This guide will teach you how to remove the internal bifold repairs near me door pins, rollers and pivots.

The first step is to gather your tools. You will save yourself some frustration by assembling all your tools in advance. You'll require a screwdriver, pliers and perhaps a wrench. A basic set of tools can be bought at a reasonable price at your local hardware store. It's also a good idea to keep some wood glue handy. This is helpful when you need to glue the rollers into place.

After gathering your tools and tools, open the bifold door and loosen the top track bracket using your screwdriver. Once this is loose the door should be able to slide off the top track completely. It may take some dancing but it should eventually pop off the track.

Next, you'll need to remove the pivot at the bottom from the frame. Close all interior doors prior to starting. This will be a lot easier than working from the inside. If the track at the bottom appears good, you can simply lift the door and take off the track.

If the track is damaged, then you'll have to replace it. Hardware stores sell replacement tracks for bifold doors, as well as swinging closet doors. If the track is badly damaged, you may have to replace it completely.

You'll now need to test your doors for the proper operation. Make sure they're capable of moving smoothly in and out of position. You'll want to ensure that the edges of your door are in line to the frame when closed. If they aren't, you'll need to adjust the top pivot bracket by tightening or loosening the bottom setscrew.

Replace the Roller

If they are installed correctly they can be used to cover pantries, laundry nooks and closets. Bifold doors comprise two panels that are hinged and slide along an incline at the top of the frame. Over time the guides for the rollers can wear out and cause the doors to slide. The guide roller can be replaced in a matter of minutes with the use of basic tools.

The first step is to remove the guide roller from the door panel. The pivot bolt at the bottom is to be removed, as well as the screw that holds the guide to the top of the door panel needs to be loosened. After removing the guide, pull the panel off the track. Next, loosen the nut that secures the top pivot bolt and use the wrench to pull it out of the hole in the top header of the door frame.

Stanley, Cox and Acme offer a replacement top nylon roller that has a 7/8-inch diameter wheel on a steel base. It is mounted on the top edge of bifold doors that range from 1 to 1-3/8 inches thick and is spring loaded to self-adjust the upper track for smooth gliding.

Another issue that is common to a bifold door is that it scrapes the floor when it closes or opens. This is often the result of adding carpet or other flooring materials that require the doors be slightly raised to allow for clearance. This issue can be fixed by removing the screws that adjust the bottom pivot, loosening up the top track mounting screws, and moving the anchor/pivot.

A new set of roller guides is a cost-effective solution to the problem of your bifold doors becoming difficult to operate. They are usually available at the hardware store near you in the door section but they're also available on the internet from a variety of sellers. In addition to a new top roller guide, you will need a small container of Elmer's wood glue which is available in big box stores as well as a squeeze clamp. The clamp is used to keep the repair bifold door top pivot area tightly closed after glue is inserted and allowed to dry.