Car Key Button Repair

A damaged car key button can be frustrating. You might need to call an emergency locksmith service 24 hours a day to help or purchase a new remote.

However, you may be able to save money by fixing an old key fob rather than replacing it. This is especially true if an old switch or damaged contacts are the reason for the issue.

Battery

If the buttons on your key fob do not respond when you pressing them, it could be a sign the battery has failed or is close to the end of life. Fortunately replacing the battery is a simple task that can be done on your own rather than paying a locksmith or dealership to complete the task for you.

Find the battery compartment first. This is usually found on the backside of the key fob. It might be hidden behind a slide-out cover or an access point that opens when you press a button. After the compartment is open you can look for the tiny button-cell battery. It's usually shaped as a coin and has the plus and minus signs. Remove the battery from the old one and replace it with a new one in its place, making sure that the plus and minus symbols are aligned correctly.

Close the compartment and snap the two parts of your key fob. Before closing the door, align and snap the pieces in the correct position. Press any of the buttons to confirm that they function properly.

If your remote key fob stops functioning even after replacing the battery, it could be experiencing other issues that require a different kind of repair car key. Physical damage caused by dropping the fob into a puddle for instance could cause it to cease functioning altogether. It could also be due to a problem with the internal electrical system or need to be deprogrammed. Try to figure out if the problem is with your key fob by applying these other typical methods for troubleshooting your car key lock repair near me.

Switches

There are a variety of switches found in the car key fob, depending on the year and make. The older style of key often has an additional chip that is visible inside the case, while the newer keys are more advanced and work by sending signals to the car. Whatever the model, the buttons on the key can get worn down or damaged during normal use. They become hard to press or not responsive. If you attempt to force the button to function the button, it could cause damage and potentially stop the key from being able to start your vehicle in the future.

If you're unable to get your key to work Try changing the batteries. If that doesn't work then you might need to clean your key fob and adjust the switches. These tiny electronic car key repair near me switches are more likely than larger components of the key to break since they are constantly jostled.

The switches have a rubbery feeling and are coated with a film that conducts electricity. The film may fade over time. Fortunately, they're a small part that is inexpensive to replace. The old ones are soldered to the circuit board, and you'll need to be careful to remove them without damaging anything else. Then, you can solder in the new ones and reassemble your key fob.

One way to prevent your car key fob from becoming damaged is to avoid using it for longer than a couple of hours at a stretch, and also to not leave it in visible locations that it will be visible. If you don't use your key, put it away in a secure location.

If the problem persists after you've cleaned the key fob replaced the battery and attempted to clean it, you may need to consult an expert locksmith. A professional can check the frequency of your key to see if it's still able to communicate with your vehicle, and open and replace micro switches, alter cases and more.

Outer Case

If the buttons don't move freely up and down in the case, they may be stuck or even break. If cleaning the case with rubbing alcohol and a cotton swab fails to work, it might be necessary to take off the case. If the contacts that the buttons touch don't fit well or are worn out, adjusting them might be the only option to fix the issue.

Certain keys have rubber buttons which can be worn out over time. Rubber buttons can become difficult to press when they stretch, and nails may gouge them. In this scenario the key may fail, and it's time to replace the case or button. This repair involves taking apart your remote, looking for the switch on the board, heating the solder, and then carefully taking them off. New buttons are then attached to the circuit board. The case can be reassembled and the horseshoe key blade can be attached. The new buttons must be fitted snugly inside the case to prevent them from falling out.

Inner Case

Over time, your key fob's buttons may become damaged or stuck as a result of the constant jostling and accidental pressing. Using metallic tape and a hole punch, you can usually solve this issue in the event your car key repair service is away from home when the key fob won't work and you are unable to open the doors, but not start the engine. This simple fix can allow you to safely make it back to your vehicle and finish your trip.